Sunday, September 9, 2007

What should you do during an EQ?

  1. If you are INDOORS--STAY THERE! (Get under a desk or table and hang on to it, or move into a hallway or get against an inside wall. STAY CLEAR of windows, fireplaces, and heavy furniture or appliances. GET OUT of the kitchen, which is a dangerous place (things can fall on you). DON'T run downstairs or rush outside while the bldg is shaking or while there is danger of falling and hurting yourself or being hit by falling glass or debris.


  2. If you are OUTSIDE-- get into the OPEN, away from bldgs, power lines, chimneys, and anything else that might fall on you.


  3. If you are DRIVING--stop, but carefully. Move your car as far out of traffic as possible. DO NOT stop on or under a bridge or overpass or under trees, light posts, power lines, or signs. STAY INSIDE your car until the shaking stops. When you RESUME driving watch for breaks in the pavement, fallen rocks, and bumps in the road at bridge approaches.


  4. If you are in a MOUNTAINOUS AREA--watch out for falling rock, landslides, trees, and other debris that could be loosened by quakes.

Friday, September 7, 2007

What emergency supplies do you need?

  1. Fire extinguisher

  2. Adequate supplies of medications that you or family members are taking

  3. Crescent and pipe wrenches to turn off gas and water supplies

  4. First-aid kit and handbook

  5. Flashlights with extra bulbs and batteries

  6. Portable radio with extra batteries

  7. Water for each family member for at least two weeks (allow at least 1 gallon per person per day) and purification tablets or chlorine bleach to purify drinking water from other sources

  8. Canned and package foods, enough for several days and MECHANICAL can opener. Extra food for pets if necessary

  9. Camp stove or barbecue to cook on outdoors (store fuel out of the reach of children)

  10. Waterproof, heavy-duty plastic bags for waste disposal.

During an EQ should you head for the doorway?

Only if you live in an old, unreinforced adobe house. In modern homes doorways are no stronger than any other parts of the house and usually have doors that will swing and can injure you. YOU ARE SAFER PRACTICING THE DUCK, COVER, AND HOLD under a sturdy piece of furniture.

Thursday, September 6, 2007

How are earthquakes recorded? How are earthquakes measured? How is the magnitude of an earthquake determined?

Earthquakes are recorded by a seismographic network. Each seismic station in the network measures the movement of the ground at the site. The slip of one block of rock over another in an earthquake releases energy that makes the ground vibrate. That vibration pushes the adjoining piece of ground and causes it to vibrate, and thus the energy travels out from the earthquake in a wave.

There are many different ways to measure different aspects of an earthquake.Magnitude is the most common measure of an earthquake's size. It is a measure of the size of the earthquake source and is the same number no matter where you are or what the shaking feels like. The Richter scale measures the largest wiggle on the recording, but other magnitude scales measure different parts of the earthquake.

Intensity is a measure of the shaking and damage caused by the earthquake, and this value changes from location to location.

Wednesday, September 5, 2007

What are the differences between explosions and earthquakes?

Both earthquakes and nuclear tests can rapidly release a large amount of energy. The energy source for small yield (typically less than 50 kilotons) thermonuclear devices is the splitting of heavy radioactive isotopes. This process produces about 20 million times the energy of each reacting atom in a chemical explosive. The energy source for an earthquake is tectonic strain accumulated by the relative motion of Earth's tectonic plates which is driven by mantle heat flow in the presence of the earth's gravitational field. In a nuclear test, all of the energy is suddenly (within milliseconds) released in the form of heat from a relatively small volume surrounding the thermo- nuclear device. The tremendous heat causes rapid expansion of a spherical cavity, which in turn generates seismic waves. The heat gradually conducts away from the cavity into the surrounding rock. However, rock is a poor conductor of heat so it can take many years for the thermal signature of the thermonuclear explosion to subside and the increase in the surface temperature above the explosion is insignificant.

Nuclear tests are also very shallow sources with the depth of burial generally less than a few hundred meters (the depth of burial is typically proportional to the cube root of the expected yield). The estimated yields of the larger Indian and Pakistani tests are approximately 2-40 kilotons. In a large earthquake, the elastic strain energy stored in the Earth's crust is released, within a few seconds to a few tens of seconds, by rupture along a fault and the strain energy is released from a relatively large volume of rock surrounding the fault rupture. For example, the magnitude 6.5 earthquake in Afghanistan (5/30/98 at 06:22:28 UTC 37.4 N, 70.0 E) had a source duration of about 5 seconds and an estimated source volume of order 4000 cubic kilometers. This earthquake also had a focal depth of 18 km. The energy release is equivalent to a 2000 kiloton nuclear explosion.

Tuesday, September 4, 2007

What is a seismometer? What are seismographs? How do they work?

A seismometer is the internal part of the seismograph, which may be a pendulum or a mass mounted on a spring; however, it is often used synonymously with "seismograph". Seismographs are instruments used to record the motion of the ground during an EQ--installed in the ground throughout the world and operate as seismographic network. The first one was developed in 1890. The earliest "seismoscope" was invented by the Chinese philosopher Chang Heng in A.D. 132. This did not record earthquakes, however. It only indicated that there was one occurring.

A seismograph is securely mounted onto the surface of the earth so that when the earth shakes, the entire unit shakes with it, EXCEPT for the mass on the spring which has inertia, and remains in the same place. As the seismograph shakes under (in the example below) the mass, the recording device on the mass records the realtive motion between itself and the rest of the instrument, thus recording the ground motion. In reality, these mechanisms are no longer manual, but instead work by measuring electronic changes produced by the motion of the ground with respect to the mass.

Monday, September 3, 2007

How much energy is released in an earthquake?

The total energy from an earthquake includes energy required to create new cracks in rock, energy dissipated as heat through friction, and energy elastically radiated through the earth. Of these, the only quantity that can be measured is that which is radiated through the earth. It is the radiated energy that shakes buildings and is recorded by seismograph.

The radiated energy can be obtained in various ways. Historically, the radiated energy was estimated empirically (from observations) from magnitude Ms through the Richter formula, log Es = 4.8 + 1.5Ms, where Es is seismic energy in Joules. In this formula, magnitude is measured first, after which the formula is used to obtain Es. With modern instrumentation, energy can be measured directly from velocity seismograms and converted to a magnitude. If Es is energy in joules, the energy magnitude Me is obtained by Me = (2/3) log Es -2.9. If Me is not available, the seismic moment Mo of an earthquake can provide an empirical estimate of radiated energy. After Mo is measured, it is converted to a moment magnitude Mw by Mw = (2/3) log Mo – 6.0 where Mo is in Newton-meters (Joules). Mw is then used as the magnitude in the Richter formula to obtain an estimate of radiated energy.

[Note that Me and Mw do not necessarily have the same numerical value because they measure different physical quantities. Mw is a magnitude that is derived from low-frequency displacement spectra whereas Me is measured from higher frequency velocity spectra. Mw is a measure of the area of rupture and the average slip across the fault, whereas is Me is a measure of the shaking from an earthquake.